STANDARD CONSTRUCTION SPECIFICATIONS

in compliance with designation M6 in Table 4.1, Concrete Aggregate Gradation Table. (e) COARSE AGGREGATE: Gravel or crushed stone conforming to AASHTO M 80. Gradation shall be in compliance with designation M67 in Table 4.1, Concrete Aggregate Gradation Table. Table 4.1 Concrete Aggregate Gradation Table (Percent Passing Sieve Sizes)

Standard Specifications for Transportation Materials and ...

given an AASHTO designation. This was done under a long-standing copyright arrangement between AASHTO and ASTM. Starting with the Thirty-First Edition, AASHTO-approved ASTM standards are not printed. Instead, the AASHTO specification includes the corresponding ASTM designation number and any AASHTO exception to the ASTM specification.

AASHTO M 6 - Standard Specification for Fine Aggregate for ...

Jan 01, 2013· M6. January 1, 1993 Standard Specification for Fine Aggregate for Portland Cement Concrete A description is not available for this item. M6. ... AASHTO R 80 - Standard Practice for Determining the Reactivity of Concrete Aggregates and Selecting Appropriate Measures for Preventing Deleterious Expansion in New Concrete Construction.

Aashto Aggregate Gradation Chart

aashto m6 gradation › See more all of the best education on Education shall meet the CDOT Concrete Aggregate Gradation Table and shall also conform to AASHTO M6: Sieve Size Percent Passing ⅜" 100 #4 95 - 100 #16 45 - 80 #50 10 - 30 … › Posted at 1 week ago

Construction Specifications for Sand Filters, Bioretention ...

AASHTO-M-43 0.375" to 0.75" geotextile fabric (if required) ASTM-D-4833 (puncture strength - 125 lb.) ASTM-D-4632 (Tensile Strength - 300 lb.) 0.08" thick equivalent opening size of #80 sieve Must maintain 125 gpm per sq. ft. flow rate. Note: a 4" pea gravel layer may be substituted for geotextiles meant to "separate" sand filter

Materials | FHWA - Transportation

Office of Federal Lands. United States Department of Transportation Federal Highway Administration. 1200 New Jersey Avenue, SE. Washington, DC 20590. …

Gradation Charts - New Enterprise Stone & Lime Co., Inc.

Gradation Charts. The charts below show typical gradations of various products based on required specifications from agencies and organizations such as state DOTs, AASHTO, etc. Anti-Skid. Coarse Aggregates. Fine Aggregates. Micro-Surfacing. Rip Rap. Aggregate. Ordering Tips.

Transportation.org – The home of transportation professionals.

AASHTO serves as a liaison between state departments of transportation and the Federal government. AASHTO is an international leader in setting technical standards for all phases of highway system development. Standards are issued for design, construction of highways and bridges, materials, and many other technical areas.

AASHTO M 6 : Standard Specification for Fine Aggregate for ...

AASHTO M 6, 2013 Edition, 2013 - Standard Specification for Fine Aggregate for Hydraulic Cement Concrete. This specification covers the quality and grading of fine aggregate for hydraulic cement concrete used in pavements or bases, highway bridges, and incidental structures. This specification is for use by a contractor, concrete supplier, or ...

MATERIALS FINER THAN No. 200 (75 µm) SIEVE IN MINERAL ...

If the sample is to be tested for gradation in accordance with AASHTO T 27, the minimum weight of that test method shall apply. If the sample is not tested for gradation in accordance with AASHTO T 27 and the nominal maximum size of aggregate to be tested is not listed in Table 1, the next larger size shall be used to determine the sample size. ...

May 2, 2001 LAB MANUAL 1219

AASHTO T 104, Table 1 is allowed for testing or calculations. G. Report the percent loss to the nearest 0.1 for each individual size . fraction. If there was a re-test report the better of the two results. H. Calculate and report the composite percent loss to the nearest 0.1 . based on the gradation …

STANDARD CONSTRUCTION SPECIFICATIONS FOR …

conform to the requirements of AASHTO M-6 and have the following gradation: Fine Aggregate for Portland Cement Concrete U.S. Standard Cumulative Sieve Size % Passing By Weight 3/8" 100 #4 95-100 #8 80-100 #16 50-85 #30 25-60 #50 10-30 #100 2-10

CITY OF WOODLAND PARK, COLORADO

by means of laboratory sieves shall meet the CDOT Concrete Aggregate Gradation Table and shall conform to AASHTO M6: Sieve Size Percent Passing 3/8" 100 #4 95 - 100 #8 80 - 100 #16 45 - 80 #30 25 - 60 #50 10 - 30 #100 2 - 10 6.2.5 COARSE AGGREGATE The coarse aggregate shall consist of broken stone or gravel composed of clean, hard, tough

AASHTO M 6 - Standard Specification for Fine Aggregate …

Jan 01, 2013· M6. January 1, 1993 Standard Specification for Fine Aggregate for Portland Cement Concrete A description is not available for this item. M6. ... AASHTO R 80 - Standard Practice for Determining the Reactivity of Concrete Aggregates and Selecting Appropriate Measures for Preventing Deleterious Expansion in New Concrete Construction.

GUIDE FOR ROLLER-COMPACTED CONCRETE PAVEMENTS

• AASHTO M6 Fine Aggregate for Portland Cement Concrete • AASHTO M80 Coarse Aggregate for Portland Cement Concrete • AASHTO T96 Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact ... Typical aggregate gradation of RCC (solid black on chart) is similar to ...

Section 69.0 - Permanent Shotcrete Facing and Wall Drainage

a) Cement: All cement shall conform to ASTM C 150/AASHTO M85, Types I, II, III or V. b) Aggregates: Aggregate for shotcrete shall meet the strength and durability requirements of AASHTO M6/M80 and the following gradation requirements: Sieve Size Percent Passing by Weight . 12.5 mm 100 . 9.50 mm 90-100 . 4.75 mm 70-85 . 2.36 mm 50-70

Aashto M6 Gradation Chart - studyeducation.org

meet the Concrete Aggregate Gradation Table 600-2 and shall also conform to AASHTO M6. 602.5 Coarse Aggregate A. The coarse aggregate shall consist of broken stone or gravel composed of clean, hard, tough and durable stone and shall be free from soft, thin, elongated or laminated pieces, disintegrated stone, clay, loam,

LETTER OF TRANSMITTAL

AASHTO M6 Section 8.1 ≤ 15 Unit Weight (Density) and Voids (ASTM C29) by Rodding Unit Weight (pcf) 106 Unit Weight (pcy) 2,853 Voids (%) 34 Organic Impurities (ASTM C40) Color Plate ASTM C33 Section 7.2.1 AASHTO M6 Section 7.2.1 1 ≤ Plate 3 (Standard) ≤ Plate 3 (Standard) Sand Equivalency (ASTM D2419) Sand Equivalent Result 88

Table 703.4 Standard Sizes of Coarse Aggregates AASHTO M43

Table 703.4 Standard Sizes of Coarse Aggregates AASHTO M43 Amounts finer than each laboratory Sieve (square openings), percentage by weight. LAUREIJ AGGREGATES . Title: Product Gradations.xlsx Author: richard.rohrssen Created Date: 10/27/2020 4:41:07 PM ...

TABLE OF CONTENTS

Coarse Aggregate(AASHTO No. 57 or 67) 1700 Fine Aggregate Sand (AASHTO M6) 1845 Air Entraining Agent 5 oz. Water (39 Gallons) 325 (or as needed for proper consistency) Flow-Fill shall have design compressive strengths of 50 to 150 psi at 28 days, when tested in accordance with ASTM D4832.

ASTM C778 - 17 Standard Specification for Standard Sand

1. Scope. 1.1 This specification covers standard sand for use in the testing of hydraulic cements. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of ...

(PDF) AASHTO-2011.pdf | sadek sinan - Academia.edu

AASHTO-2011.pdf. 907 Pages. AASHTO-2011.pdf. Sadek Sinan. Download PDF. Download Full PDF Package. This paper. A short summary of this paper. 32 Full PDFs related to this paper. Read Paper. AASHTO-2011.pdf.

32 16 00 Sidewalks, Curbs, and Gutters - MHFD

Transportation, Section 703.01 requirements and gradation as shown above. Fine aggregate for concrete shall conform to the requirements of AASHTO M6. The amount of deleterious substances removable by elutriation shall not exceed three percent (3%) by dry weight of fine aggregate when tested in accordance with AASHTO T11, unless otherwise specified.

Design criteria for bioretention - Minnesota Stormwater Manual

Jun 15, 2021· AASHTO M-6 or ASTM C-33 washed sand. Top Soil in the mix will help with some nutrient removal, especially nutrients, but extra care must be taken during construction to inspect the soils before installation and to avoid compaction. Organic Matter: MnDOT Grade 2 compost (See Specification 3890, page 685) is recommended.

Roller Compacted Concrete

Products falling within the fine and coarse bands may be blended at appropriate proportions to produce the desired combined gradation. Coarse Aggregates. Coarse aggregates meeting ASTM C33/AASHTO M6/M80 standards are recommended for Roller Compacted Concrete mixtures.

DESIGN AND CONSTRUCTION STANDARDS CHAPTER 8 …

indicate the aggregate gradation, asphalt cement content, hydrated lime content, and optimum density. If requested by the Director, a sample of the aggregate and ... Fine Aggregate, AASHTO M6, percent of total aggregate 50 - 78 (a) An approved water reducing admixture shall be used in the mix.

STUDY ON THE EFFECTS OF MIXTURE PROPORTIONING ON …

a bridge deck, the concrete mix shall consist of a minimum 55 percent AASHTO M 43 size No. 67 coarse aggregate by weight of total aggregate [1]. II. Sieve Analysis The sieve analysis was performed for both sand and coarse aggregate. According to the ASTM standard C 136 (AASHTO M6) the sieves required for the sand are No. 4, 8, 16, 30, 50, 100 ...

Sand material specifications - Minnesota Stormwater Manual

clean AASHTO M-6 or ASTM C-33 concrete sand: 0.02" to 0.04" Sand substitutions such as Diabase and Graystone #10 are not acceptable. No calcium carbonated or dolomitic sand substitutions are acceptable. Rock dust cannot be substituted for sand. Underdrain Gravel: AASHTO M-43: 1.5" to 3.5" Geotextile Fabric (if required)

AGGREGATES - University of Wyoming

AASHTO M6 except deleterious ... Gradation Requirements: Coarse Aggregate for Concrete (1) For these, and for class A concrete used for pavement, ensure that at least 50 percent of the material retained on the No. 4 [4.75 mm] sieve has at least one fractured face.

SAND SPECIFICATIONS

1. Sand must meet gradation requirements for ASTM C-33 Fine Aggregate Concrete Sand. AASHTO M-6 gradation is also acceptable. 2. Sand must be silica based … no limestone based products may be used. If the material is white or gray in color, it is probably not acceptable. 3. Sand must be clean. Natural, unwashed sand deposits may not be used ...

CHAPTER 6 – BRIDGES AND MAJOR DRAINAGE STRUCTURES …

For concrete-aggregate gradation see Table 6.3. F. An approved water reducer will be required for this class. G. The design slump will be between 1 and 2-1/2 inches and will be shown on the ... AASHTO M6 SIEVE SIZE 2" to 1" 1-1/2" to 3/4"

AASHTO Soil Classification System - AASHTO Chart

Oct 01, 2019· Besides Soil Classification on other criteria, the AASHTO Soil Classification System classifies soils into seven primary groups, named A-1 through A-7, based on their relative expected quality for road embankments, sub-grades, sub-bases, and bases.Some of the groups are in turn divided into subgroups, such as A-1-a and A-1-b.Furthermore, a Group Index may be calculated to quantify a …

C4.11 SWM DETAILS AND SPECIFICATIONS SC015SWDETAIL

In addition to the ASTM C33 specification, sand must meet ALL of the following conditions: 1. Sand must meet gradation requirements for ASTM C-33 Fine Aggregate Sand must meet gradation requirements for ASTM C-33 Fine Aggregate Concrete Sand. AASHTO M-6 gradation is also acceptable. 2. Sand must be silica based; no limestone based products may ...

UG-Mat Reclaimed Concrete Material | Recycled Materials ...

Gradation: Recycled concrete material should be crushed and screened to produce aggregate that satisfies the AASHTO M6 (3) and M80 (4) gradation requirements for PCC. With appropriate adjustments, a plant can produce any desired gradation.

Sand / Media Specifications

Washington State Department of Health Wastewater Management Program RULE DEVELOPMENT COMMITTEE ISSUE RESEARCH REPORT – DRAFT - SAND/MEDIA SPECIFICATIONS- Page 3 of 10 therefore it is important that filters using this size sand be …

AASHTO M 80 : Standard Specification for Coarse Aggregate ...

AASHTO M 80, 2013 Edition, 2013 - Standard Specification for Coarse Aggregate for Hydraulic Cement Concrete. This specification covers coarse aggregate, other than lightweight aggregate, for use in concrete. Several classes and gradings of coarse aggregate are described (Notes 1 and 2). Specifications for fine aggregate are provided in M 6.

SECTION 600 - CONCRETE WORK TABLE OF CONTENTS PAGE

meet the Concrete Aggregate Gradation Table 600-2 and shall also conform to AASHTO M6. 602.5 Coarse Aggregate A. The coarse aggregate shall consist of broken stone or gravel composed of clean, hard, tough and durable stone and shall be free from soft, thin, elongated or laminated pieces, disintegrated stone, clay, loam,